IBIS List Email Archive: IBIS BIRD71 - Timing Test Loads in [Mod

From: Bob Ross <bob_ross@mentorg.com>
Date: Mon Apr 30 2001 - 15:19:51 PDT

To IBIS Committee:

Stephen Peters is submitting BIRD71 for consideration in IBIS Version 4.0.

Bob Ross
Mentor Graphics

******************************************************************************
******************************************************************************

BIRD ID#: 71
ISSUE TITLE: Timing Test Loads in [Model Spec] to Support PCI & PCI-X
REQUESTER: Stephen Peters, Intel Corp.
DATE SUBMITTED: April 30, 2001
DATE ACCEPTED BY IBIS OPEN FORUM: Pending

******************************************************************************
******************************************************************************

STATEMENT OF THE ISSUE:

The IBIS specification lacks a way to specify minimum and maximum values
for timing test load parameters. In addition, the current set of timing test
load parameters (Cref, Rref) are applied to both edges of an output waveform,
thus making them inadequate for describing the timing tests loads used by
the PCI-X bus specification.

******************************************************************************

STATEMENT OF THE RESOLVED SPECIFICATIONS:

The following additional subparameters are added to the [Model Spec] keyword:
Cref, Rref, Vref_rising, Vref_falling, Cref_rising, Cref_falling, Rref_rising,
Rref_falling, Vmeas_rising, Vmeas_falling.

Changes and additions to the [Model Spec] keyword are shown by the |* lines

|=============================================================================
| Keyword: [Model Spec]
| Required: No
| Sub-Params: Vinh, Vinl, Vinh+, Vinh-, Vinl+, Vinl-, S_overshoot_high,
| S_overshoot_low, D_overshoot_high, D_overshoot_low,
| D_overshoot_time, Pulse_high, Pulse_low, Pulse_time, Vmeas
|* Vref, Cref, Rref, Cref_rising, Cref_falling, Rref_rising,
|* Rref_falling, Vref_rising, Vref_falling, Vmeas_rising,
|* Vmeas_falling.
| Description: The [Model Spec] keyword defines four columns under which
| specification subparameters are defined.
|
| The following subparameters are defined:
| Vinh Input voltage threshold high
| Vinl Input voltage threshold low
| Vinh+ Hysteresis threshold high max Vt+
| Vinh- Hysteresis threshold high min Vt+
| Vinl+ Hysteresis threshold low max Vt-
| Vinl- Hysteresis threshold low min Vt-
| S_overshoot_high Static overshoot high voltage
| S_overshoot_low Static overshoot low voltage
| D_overshoot_high Dynamic overshoot high voltage
| D_overshoot_low Dynamic overshoot low voltage
| D_overshoot_time Dynamic overshoot time
| Pulse_high Pulse immunity high voltage
| Pulse_low Pulse immunity low voltage
| Pulse_time Pulse immunity time
|
| Vmeas Measurement voltage for timing measurements
| Vref Timing specification test load voltage
|* Cref Timing specification capacitive load
|* Rref Timing specification resistance load
|* Cref_rising Timing spec capacitive load for rising edges
|* Cref_falling Timing spec capacitive load for falling edges
|* Rref_rising Timing spec resistance load for rising edges
|* Rref_falling Timing spec resistance load for falling edges
|* Vref_rising Timing spec test load voltage for rising edges
|* Vref_falling Timing spec test load voltage for falling edges
|* Vmeas_rising Measurement voltage for rising edge timing
|* measurements
|* Vmeas_falling Measurement voltage for falling edge timing
|* measurements
|
| Usage Rules: [Model Spec] must follow all other subparameters under the
| [Model] keyword.
|
| For each subparameter contained in the first column, the
| remaining three hold its typical, minimum and maximum values.
| The entries of typical, minimum and maximum be must be placed
| on a single line and must be separated by at least one white
| space or tab character. All four columns are required under
| the [Model Spec] keyword. However, data is required only in
| the typical column. If minimum and/or maximum values are not
| available, the reserved word "NA" must be used indicating the
| typical value by default.
|
| The minimum and maximum values are used for specifications
| subparameter values that may track the min and max operation
| conditions of the [Model]. Usually it is related to the
| Voltage Range settings.
|
| Unless noted below, each subparameter does not require having
| any other subparameter.
|
| Vinh, Vinl rules:
|
| The threshold subparameter lines provide additional min and
| max column values, if needed. The typ column values are still
| required and would be expected to override the Vinh and Vinl
| subparameter values specified elsewhere. Note: the syntax
| rule that require inserting Vinh and Vinl under models remains
| unchanged even if the values are defined under the [Model
| Spec] keyword.
|
| To mimic a hysteresis effect, the values of Vinh and Vinl may
| be interchanged such that the Vinl value is larger than the
| Vinh value. However, simulators may process this information
| differently or report an error.
|
| Vinh+, Vinh-, Vinl+, Vinl- rules:
|
| The four hysteresis subparmeters must all be defined before
| the hysteresis threshold rules become effective. Otherwise
| the standard threshold subparameters remain in effect. The
| hysteresis thresholds shall be at the Vinh+ and Vinh- values
| for a low-to-high transition, and at the Vinl+ and Vinl-
| values for a high-to-low transition.
|
| S_overshoot_high, S_overshoot_low rules:
|
| The static overshoot subparameters provide the voltage values
| for which the model is no longer guaranteed to function
| correctly.
|
| D_overshoot_high, D_overshoot_low, D_overshoot_time rules:
|
| The dynamic overshoot values provide a time window during
| which the overshoot may exceed the static overshoot limits
| but be below the dynamic overshoot limits. D_overshoot_time
| is required for dynamic overshoot testing. In addition, if
| D_overshoot_high is specified, then S_overshoot_high is
| necessary for testing beyond the static limit. Similarly, if
| D_overshoot_low is specified, then S_overshoot_low is
| necessary for testing beyond the static limit.
|
| Pulse_high, Pulse_low, Pulse_time rules:
|
| The pulse immunity values provide a time window during which
| a rising pulse may exceed the nearest threshold value but
| be below the pulse voltage value and still not cause the
| input to switch. Pulse_time is required for pulse immunity
| testing. A rising response is tested only if Pulse_high is
| specified. Similarly, a falling response is tested only if
| Pulse_low is specified. The rising response may exceed the
| Vinl value, but remain below the Pulse_high value.
| Similarly, the falling response may drop below the Vinh value,
| but remain above the Pulse_low value. In either case the
| input is regarded as immune to switching if the responses
| are within these extended windows. If the hysteresis
| thresholds are defined, then the rising response shall use
| Vinh- as the reference voltage, and the falling response shall
| use Vinl+ as the reference voltage.
|
|* Vmeas, Vref, Cref, Rref rules:
|*
|* The Vmeas, Vref, Cref and Rref values under the [Model Spec]
|* keyword override their respective values entered elsewhere.
|* Note that a Vmeas, Vref, Cref or Rref subparameters may not be
|* used if its edge specific version (*_rising or *_falling) is
|* used.
|*
|* Cref_rising, Cref_falling, Rref_rising, Rref_falling,
|* Vref_rising, Vref_falling, Vmeas_rising, Vmeas_falling rules:
|*
|* Use these subparameters when specifying separate timing test
|* loads and voltages for rising and falling edges. If one
|* 'rising' or 'falling' subparameter is used, then the
|* corresponding 'rising' or 'falling' subparameter must be
|* present. The values listed in these subparameters override any
|* corresponding Cref, Vref, Rref or Vmeas values entered
|* elsewhere.

******************************************************************************

ANALYSIS PATH/DATA THAT LED TO SPECIFICATION:

BIRDxx is issued because of a long standing problem with specifying PCI
compliant drivers. In PCI 2.2, minimum timing values are specified into
a 0pF load, while maximum timing parameters are specified into a 50pF
load. There was no way to specify this cleanly in IBIS.

In addition, the PCI-X specification goes even further in specifying separate
timing test loads for maximum rising and falling edges, and a single test
load for the minimum case. In order to satisy the PCI-X spec all eight
variations of Cref, Vref, Rref and Vmeas has to be included. Note that the
PCI-X minimum test load is represented by it's Thevinen equivalent.

******************************************************************************

ANY OTHER BACKGROUND INFORMATION:

******************************************************************************

Received on Mon Apr 30 15:20:36 2001

This archive was generated by hypermail 2.1.8 : Fri Jun 03 2011 - 09:52:30 PDT

IBIS BIRD71 - Timing Test Loads in [Model Spec] to Support PCI & PCI-X