RE: another C_comp confusion question

From: Dagostino, Tom <tom_dagostino@mentorg.com>
Date: Wed May 16 2001 - 12:03:48 PDT

The smallest specified C_comp I've seen is around 700fF. The largest
spec'ed beleive it or not was around 35 pF. Most of what I have seen falls
in the range Milt points out. Remember, the data from a datasheet usually
has some pad in it.

-----Original Message-----
From: Milt Schwartz x3261 [mailto:schwartz@galaxy.nsc.com]
Sent: Wednesday, May 16, 2001 11:49 AM
To: ibis@eda.org
Subject: RE: another C_comp confusion question

Our C_comp measurements at National Semiconductor Interface Group.
Based on bench TDR, subtracting out the package parameter which we get in a
matrix from our packaging group.

LVDS differential driver outputs; range is 3.15pF to 5.3pF depending on how
"strong" the driver output is and the type of ESD protection circuitry.

Receiver outputs, are full CMOS swing: Range from 5pF to 7pF, again
depending on how "strong" the output is and the type of ESD protection.

These are all CMOS process, typically 0.35 micrometer.

regards, milt schwartz
Interface Applications

> From owner-ibis@server.eda.org Wed May 16 08:36:48 2001
> From: Bob Khederian <RKhederian@whiteedc.com>
> To: "'Wilco Hamhuis'" <w.hamhuis@transfer.nl>, Ibis <ibis@eda.org>
> Subject: RE: another C_comp confusion question
> Date: Wed, 16 May 2001 10:50:46 -0400
> MIME-Version: 1.0
> X-Mailer: Internet Mail Service (5.5.2653.19)
> Sender: owner-ibis@server.eda.org
>
> Hi All,
>
> I have also had a problem with Ccomp, but the other extreme. I have seen
> Ccomp values of 5pF. Recall according to the IBIS spec, "Ccomp defines
the
> silicon die capacitance". I find it difficult to beleive that the
> capacitance of a die (we deal with memory here) is 5pF. Has anyone had
> similar concerns? Has anyone addressed this with any of the silicon
> vendors?
>
> Bob.
>
> -----Original Message-----
> From: Wilco Hamhuis [mailto:w.hamhuis@transfer.nl]
> Sent: Wednesday, May 16, 2001 9:40 AM
> To: Ibis
> Subject: another C_comp confusion question
>
>
> Hi all,
>
> Betty Luk initiated this topic a few months ago. Recently I received a
> differential IBIS model from a vendor. I noticed that the C_comp value was
> very small, 162fF. Apparently the C_comp value is also included in the VT
> tables. In my case I don't have the VT tables. The driver model only
> consists out of the pullup and down curves. Gnd, power, rise and fall
aren't
> present (ramp data is present). When I use this model in a XTK simulation
I
> see very large oscillation, straight through the logic threshold levels.
> Increasing the C_comp value a bit and the results become significant
better.
> I find it VERY disturbing that C_comp has such a large impact on the
> simulation results. My questions:
>
> - is 162fF a realistic C_comp value according to your experience?
> - does anyone have any experience with questionable simulation results
due
> to C_comp value?
> - what is the relationship between the VT tables and C_comp?
>
> Tanks in advance,
>
> Wilco
> Signal Integrity Expert
>

 
Received on Wed May 16 12:05:53 2001

This archive was generated by hypermail 2.1.8 : Fri Jun 03 2011 - 09:52:30 PDT