RE: [IBIS] RE: [IBIS-Users] hspice vs IBIS model correlation at different capacitive loads

From: Itzik Peleg <itzikpe_at_.....>
Date: Tue Dec 13 2005 - 23:19:45 PST
Hello Venu

 

Just to add one more possibility doe's your buffer has a feedback?

Could you attached the IBIS model, or show the I(V) and V(t) curves?

 

--
Regards
 
Itzik Peleg
Board Technology Group
 
Marvell Semiconductor Israel Ltd
6 Hamada Street 

Mordot HaCarmel Industrial Park

Yokneam 20692, ISRAEL
 
Email - itzikpe@marvell.com
Tel   - +972 4  9091192
Cell  - +972 54 4452482
Fax   - +972 4  9091501
WWW Page: http://www.marvell.com <BLOCKED::http://www.marvell.com> 
========================================================================
This message may contain confidential, proprietary or legally privileged
information. The information is intended only for the use of the
individual or entity named above. If the reader of this message is not
the intended recipient, you are hereby notified that any dissemination,
distribution or copying of this communication is strictly prohibited.
If you have received this communication in error, please notify us
immediately by telephone, or by e-mail and delete the message from
your computer.
 
Thank you!
========================================================================
________________________________


From: owner-ibis@eda.org [mailto:owner-ibis@eda.org] On Behalf Of
Ummalaneni, Venu Babu (Venu)
Sent: Tuesday, December 13, 2005 2:49 PM
To: Todd Westerhoff (twesterh); ibis-users@eda.org; ibis@eda.org
Subject: [IBIS] RE: [IBIS-Users] hspice vs IBIS model correlation at
different capacitive loads

 

Todd,

 

Thanks for your inputs. 

 

I have verified the programming options of driver and it's fine. Here, I
am attaching the correlation waveforms of the simulations by using a 0.1
ohm resistor instead of transmission line in both load (5pF & 30pF)
cases. Still, I am seeing a bad correlation in 30pF case.

 

Please ignore my previously attached *.PDF.

 

Once again thanks for your response.

 

Best Reagrds,

Venu

 

 

-----Original Message-----
From: Todd Westerhoff (twesterh) [mailto:twesterh@cisco.com] 
Sent: Tuesday, December 13, 2005 5:43 PM
To: Ummalaneni, Venu Babu (Venu); ibis-users@eda.org; ibis@eda.org
Subject: RE: [IBIS-Users] hspice vs IBIS model correlation at different
capacitive loads

 

Venu,

 

How long is the transmission line you're using ... about 1ns?

 

Your IBIS driver in the 30pf case seems to be taking several round-trips
to charge the load where the HSpice driver doesn't - if this is a
programmable driver, is it possible the driver settings for the two
plots are different?  In the top plot for the 30pf case, the IBIS driver
looks like a much weaker output with a faster slew rate to me ...

 

Todd.


Todd Westerhoff
High Speed Design Group Manager
Cisco Systems
1414 Massachusetts Ave
Boxboro, MA 01719
email:twesterh@cisco.com
ph: 978-936-2149
____________________________________________
"Always do right.
 This will gratify some people and astonish the rest."

 

- Mark Twain

 

 

________________________________

From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org] On
Behalf Of Ummalaneni, Venu Babu (Venu)
Sent: Tuesday, December 13, 2005 5:38 AM
To: ibis-users@eda.org; ibis@eda.org
Subject: [IBIS-Users] hspice vs IBIS model correlation at different
capacitive loads

Hi Gurus,

I have an ATA* IBIS model and it is correlating well with hspice model
when I am using a 5pF load followed by a transmission line. If I replace
the 5pF load with 30pF correlation is bad (particularly in 2nd page
waveform of attached PDF). 

Could some one comment on this, where it is going wrong?

Your comments/inputs are highly appreciated.

Attachments: ata4nik_5pf.pdf - hspice and IBIS model waveforms captured
using 5pF load

                    ata4nik_30pf.pdf - hspice and IBIS model waveforms
captured using 30pF load

Thanks & Best Regards,

Venu

<<ata4n1k_30pf.pdf>> <<ata4n1k_5pf.pdf>> 


-----------------------------------------------------------------
|For help or to subscribe/unsubscribe, email majordomo@eda.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or email a request to ibis-request@eda.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda.org/pub/ibis/email_archive/  Recent
|  http://www.eda.org/pub/ibis/users_archive/  Recent
|  http://www.eda.org/pub/ibis/email/          E-mail since 1993
Received on Tue Dec 13 23:20:17 2005

This archive was generated by hypermail 2.1.8 : Tue Dec 13 2005 - 23:24:09 PST