[IBIS] RE: [IBIS-Users] How to include Differential and Normal IO's of same pins

From: Tom Dagostino <tom_at_.....>
Date: Thu Apr 06 2006 - 10:09:05 PDT
Lynne

I think you are missing the point.  The two pins used for a differential
pair in one case are able to be driven by single ended buffers in a
non-differential mode at other times.  The best solution to this that I can
think of is to use a model selector to toggle between the differential
buffer and the SE buffer.  But when in the SE mode, comment out the [Diff
pin] section for those 2 pins.

Tom Dagostino
Teraspeed(R) Labs
13610 SW Harness Lane
Beaverton, OR 97008
503-430-1065
tom@teraspeed.com
www.teraspeed.com

Teraspeed Consulting Group LLC
121 North River Drive
Narragansett, RI 02882
401-284-1827

-----Original Message-----
From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org]On
Behalf Of Lynne D. Green
Sent: Thursday, April 06, 2006 10:01 AM
To: seshadri.kirankumar@wipro.com; ibis@eda.org; ibis-users@eda.org
Subject: RE: [IBIS-Users] How to include Differential and Normal IO's of
same pins


Hello, Kiran Kumar,

Here is an example using the same IBIS buffer for both differential and
non-differential buffers. If the buffer is fully symmetric (same edge rate,
edge delay, etc.), then one can (should) use the same model for both sides
of the diff I/O.  This also removes the need to set two model selectors for
one diff pair.

Also, since tdelay_typ defaults to 0nsec, I would recommend setting it
explicitly to that value.

[Pin]     signal_name      model_name              R_pin        L_pin
C_pin
|
Pin1         CLKP             io1
Pin2         CLKN            io1
Pin3         Single              io1
|
[Diff_pin]       inv_pin         vdiff       tdelay_typ     tdelay_min
tdelay_max
|
Pin1             Pin2            200mV      0.0n              NA
NA
|

Best regards,
Lynne


"IBIS training when you need it, where you need it."

Dr. Lynne Green
Green Streak Programs
http://www.greenstreakprograms.com
425-788-0412
lgreen22@mindspring.com




________________________________

	From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org] On
Behalf Of seshadri.kirankumar@wipro.com
	Sent: Thursday, April 06, 2006 6:10 AM
	To: ibis@eda.org; ibis-users@eda.org
	Subject: [IBIS-Users] How to include Differential and Normal IO's of
same pins



	Hi Experts,



	          I have a doubt regarding IBIS model of incorporating
Differential and Non-differential Buffers in the same IBIS file



	As an Example there are 2 pins and corresponding LVDS definition is
as follows

	[Pin]     signal_name      model_name              R_pin
L_pin         C_pin

	|

	Pin1         CLKP             LVDS_1

	Pin2         CLKN             LVDS_2

	|

	[Diff_pin]       inv_pin         vdiff       tdelay_typ
tdelay_min     tdelay_max

	|

	Pin1             Pin2            200mV      NA              NA
NA



	For  the same 2 above pins there exist normal(Non differential) IO's
too,  my doubt is that will it be possible to include both Differential and
Normal IO's with any IBIS mechanism like how a {Model Selector] chooses
different models for the same pin? If so please let me know on how?



	    Suppose same if I do using [Model Selector] then what will be
the impact of [Diff_pin] section on this pins when I am using only Normal
models, this prototype is as listed below

	[Pin]     signal_name      model_name              R_pin
L_pin         C_pin

	|

	Pin1         CLKP             MODEL_1

	Pin2         CLKN             MODEL_2

	|

	[Diff_pin]       inv_pin         vdiff       tdelay_typ
tdelay_min     tdelay_max

	|

	Pin1             Pin2            200mV      NA              NA
NA

	|

	[Model Selector]     MODEL_1

	LVDS_1                     lvds model

	BUFFER_1                 normal output buffer

	|

	[Model Selector]     MODEL_2

	LVDS_2                     lvds model

	BUFFER_2                 normal output buffer

	|

	What my opinion is option 2 is not proper as there is still
valid(uncommented) [Diff_pin]  section exist for the same pins while using
normal IO's mode, please correct me if my concept is wrong



	Any Help on this is appreciable



	Thanks & Best Regards

	Kiran Kumar




















	The information contained in this electronic message and any
attachments to this message are intended for the exclusive use of the
addressee(s) and may contain proprietary, confidential or privileged
information. If you are not the intended recipient, you should not
disseminate, distribute or copy this e-mail. Please notify the sender
immediately and destroy all copies of this message and any attachments.

	WARNING: Computer viruses can be transmitted via email. The
recipient should check this email and any attachments for the presence of
viruses. The company accepts no liability for any damage caused by any virus
transmitted by this email.

	www.wipro.com




|------------------------------------------------------------------
|For help or to subscribe/unsubscribe, email majordomo@eda.org
|with just the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or email a written request to ibis-request@eda.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda.org/pub/ibis/email_archive/  Recent
|  http://www.eda.org/pub/ibis/users_archive/  Recent
|  http://www.eda.org/pub/ibis/email/          E-mail since 1993


-----------------------------------------------------------------
|For help or to subscribe/unsubscribe, email majordomo@eda.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or email a request to ibis-request@eda.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda.org/pub/ibis/email_archive/  Recent
|  http://www.eda.org/pub/ibis/users_archive/  Recent
|  http://www.eda.org/pub/ibis/email/          E-mail since 1993
Received on Thu Apr 6 10:09:01 2006

This archive was generated by hypermail 2.1.8 : Thu Apr 06 2006 - 10:09:09 PDT