RE: [IBIS] About Fork in The Package Model

According to the IBIS 4.2 specification FORK and ENDFORK are allowed in
package models. I haven't seen them used in package models in a long
time. The only use I saw for FORK in a package model was to represent
the plating traces in ceramic PGA packages. That's been a few years ago.
So the answer to the original question is that the branch didn't go
anywhere. In the actual finished package the plating traces were just
stubs off the signal trace. They needed to be modeled correctly because
of the impedance discontinuity that they created.

Regards,
Weston


-----Original Message-----
From: owner-ibis@server.eda.org [mailto:owner-ibis@server.eda.org] On
Behalf Of Lynne D. Green
Sent: Monday, May 07, 2007 9:42 AM
To: 'Yasser Sabry'; ibis@server.eda-stds.org
Subject: RE: [IBIS] About Fork in The Package Model

Hello, Yasser,

FORK and ENDFORK not allowed in PKG models.
FORK and ENDFORK are allowed in EBD and ICM models.

- Lynne 


"IBIS training when you need it, where you need it."

Dr. Lynne Green
Green Streak Programs
http://www.greenstreakprograms.com
425-788-0412
lgreen22@mindspring.com

-----Original Message-----
From: owner-ibis@eda.org [mailto:owner-ibis@eda.org] On Behalf Of Yasser
Sabry
Sent: Sunday, May 06, 2007 9:11 AM
To: ibis@eda-stds.org
Subject: [IBIS] About Fork in The Package Model

Hi all,

Fork is used to make branches. In EBD, it is clear where these branches
go
to as the destination node or pin is specified. However, in package
model
the destination is not clear for me. Where do the branches go to?

Thanks for your help,
Yasser Sabry

-------------------------------------------
Yasser Mohammed Sabry
Device Modeling Team
Analog/Mixed Signal - DSM Division
Mentor Graphics Egypt
Tel: (+202) 416 3613
Mob: (+2010) 1834833
Fax: (+202) 418 6945
E-mail: yasser_sabry@mentor.com
-------------------------------------------




-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.

--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993