[IBIS] RE: Trimming V-t curves - IBIS model behavior in over clocking mode

From: Ummalaneni, Venu Babu (Venu) <Venu.Ummalaneni_at_.....>
Date: Wed Nov 28 2007 - 20:12:37 PST
Dmitry and all,

I am curious to know your experiences on the experiments with "trimming
V-t curves". Could some one please comment on the behavior of IBIS model
with Hspice simulator before and after trimming? I mean, whether the
correlation of the IBIS vs golden model in over clocking mode improved
after trimming the V-t curves?

Thanks & Best Regards,
Venu

-----Original Message-----
From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org] On
Behalf Of Dimitry Eisenshtat
Sent: Tuesday, January 16, 2007 3:32 AM
To: Todd Westerhoff
Cc: ibis@eda-stds.org; ibis-users@eda.org
Subject: Re: [IBIS-Users] RE: [IBIS] Ibis open drain strange behaviour

Hi Todd,
first of all - thanks for your reply, as I said, I'm writing script for
trimming V/T tables in order to satisfy Cookbook recommendation, so your
explanation is really useful. Thank you :)

Ok, I see from your virtual DDR example that "over clocking" should
require special treatment on IBIS simulator side, and I finally decide
to avoid such situations and create IBIS models with V/T tables time
window up to  half of minimum signal period the buffer designed for.

Now some words about HOW I will do it. I think the most important point
you mentioned is "time correlation" of all given corner curves. I want
use simple algorithm for automatically trimming V/T curves, let me
explain. Lets say we have 12 transients, exactly as in your (most
common) example of push-pull buffer simulated in 3 corners with load of
50 ohm once to supply, once to ground. The steps will be:

1) Run spice simulations (with s2ibis* or manually, does not matter)
with as small time step as it possible for simulation time large enough
for weakest conditions (corner/load) transition to be finally completed.

The idea is to begin with "ideal" time resolution for all transitions
regions in our 12 curves.

2) For each curve find largest time interval (T1,T2) which satisfy
voltage tolerance of delta from initial and final DC solutions, i.e.
  |(V(T1)-Vstart)/VDD|  < Vtol,
  |(V(T2)-Vend)/VDD|    < Vtol
where Vtol tolerance chosen smaller than IBISCHK's one so the checker
will not report "DC endpoints" warning on trimmed tables latter. All
data points outside of this interval (T1,T2) are declared "dead zones" 
and have no importance. So the Vtol value actually plays as "dead zones"

definition criteria and should be the parameter to be changed if needed.

3) For all curves (rising/falling/load) of given corner find the minimum
T1 value, lets define it as T1_typ, T1_slow, T1_fast or T1_<corner>.

4) Calculate maximum interval dT_max = max {|T2-T1_<corner>|} for ALL
curves.

5) Shift all curves for given corner left in time by T1_<corner> value.

6) Truncate all curves at time dT_max (from new 0 time after shifting)

7) Add one points to end of each curve in order to form a line with zero
slope for case of some simulators extrapolation will be needed.

8) Remember, we start from "the best" time resolution, so it is possible
that we get desire time window from overclocking point of view, but
number of points in final V/T tables still exceeds the maximum allowed
by IBIS spec. In this case I suggest to use "greatest change algorithm" 
in order to decrease the number of tables points, as it described in
Cookbook (pages 63-64).

As the result, if I have no mistake, we will get "corner time-
correlated" tables. However, across corners correlation is not
guaranteed. My assumption is that the user will be interested in
analyzing the buffer's (buffer itself, I mean not control logic but
pullup/pulldown devices which actually drive the pad) corner-specific
behavioral/differences, so I at least do not worsen the model quality,
or even improve it. Anyway,  in some cases there will be no possibility
to satisfy "overclocking free" condition without shifting the corner's
curves one to each other, in other words without trimming different
amounts from different corners.

Does it make sense? I like to complete realizing this algorithm in perl
and try it on last DDR2 model I produced. Only IBIS simulator I have is
HSpice, so the plan is to compare the behavioral of IBIS model before
and after trimming. I hope the HSpice is bad enough in "over clocking" 
scenario, otherwise I will see no difference/improvements anyway :)

Regards,
    Dmitry


Todd Westerhoff wrote:
> Sorry for the delay in reply - I took the weekend off ;-)
> 
> As far as non-time correlation between IBIS and transistor models goes
> - no, it isn't a problem at all.  It's just important that people 
> understand what a model represents and what it doesn't, so that they 
> can draw the right conclusions from their simulations.  I was just 
> re-iterating one of my favorite points with "time 0 in an IBIS model
is arbitrary".
> 
> To your point, it's worth noting that time 0 in a spice model-based 
> simulation is often arbitrary as well.  A spice model represents only 
> the output buffer at most, so if you're analyzing a device with a 
> clock-to-out timing specification, you still need to figure out how to

> combine the delays measured in simulation with the timing spec for the
device.
> 
> I think people often ascribe too much credibility to spice models.  
> The model you receive is a function of how the netlist and parasitics 
> for the buffer were extracted - it's far too easy to become confused 
> about what part of the overall device the spice model represents.
> 
> As to page 70 of the IBIS cookbook - I agree with what it says.  That 
> particular page is assuming a DDR device, so that a 100 MHz clock 
> yields 200M transfers/sec, each with a 5 ns UI.  Let's suppose you 
> have a model with a 6ns rising V-T curve for this case.  The simulator

> will trigger the curve, begin sweeping the output, and then get 
> retriggered at the 5ns point
> - before the rising edge is complete.  What should the simulator do?
> 
> - should it just jump to the start of the falling curve (if it does, 
> you may get a discontinuity on the output that can either glitch the 
> output or cause a convergence problem)
> 
> - should the simulator "pipeline" the waveform results, and just 
> remember the next edge starts 1 ns later - and if the input edges keep

> coming faster than the curve length, how long should the simulator 
> keep this up before it starts clipping data?
> 
> ... my earlier point was that the IBIS spec has no guidance on how a 
> simulator should handle "overclocking" and different simulators DO 
> handle this issue different ways.  That being the case, it's best to 
> avoid the problem by complying with the strong recommendation on page
70.
> 
> As far as curve trimming goes, allow me to provide a *brief* overview,

> although I'm sure this subject has been discussed previously.
> Pointers into the archive for this subject from others would be
appreciated.
> 
> Let's consider a push-pull output stage instead of open drain - 
> open-drain will just be a simpler case.
> 
> Each output should have the following V-T curves
> 	
> 	[Corners]         x [Edge]             x [Loading]
> 
> 	[Min / Typ / Max] x [Rising / Falling] x [50 ohms GND / 50 ohms
VDDQ]
> 
> ... for a total of 12 sets of V-T curves.  
> 
> ... for each [Corner]/[Loading] combination, it is ESSENTIAL that if 
> you trim dead time off one curve, you trim the SAME amount of dead 
> time off the other.  As an example, if you trim 1ns off the start of 
> the [Min]/[Rising]/[50 ohms GND] curve, you MUST trim 1ns off the 
> [Min]/[Rising]/[50 ohms VDDQ] curve.  If the second curve was already 
> rising at that point, well, you need to trim less.
> 
> This is what's called "time correlation" between curves, and it must 
> be maintained.
> 
> ... good practice dictates that you coordinate your trimming across 
> all four of the V-T waveforms for any corner.  If you don't do this, 
> you'll introduce duty cycle distortion into the simulated waveform 
> without meaning to.  I believe this is now considered to be required 
> practice.  So, if you trim 1ns off the start of the [Min]/[Rising]/[50

> ohms GND] curve, you really, really should trim 1ns off the following
curves:
> 
> 	[Min]/[Rising]/[50 ohms VDDQ]
> 	[Min]/[Falling]/[50 ohms GND]
> 	[Min]/[Falling]/[50 ohms VDDQ]
> 
> ... so that time correlation is maintained across all the [Min] 
> curves.  As before, if you go to trim any of the curves and find the 
> transition was already starting, you need to trim less.
> 
> I don't believe IBIS requires that you coordinate trimming across
corners.
> Thus, you can trim different amounts from the [Min] and [Typ] curve
sets.
> In practice, you'll find this is useful because if you try to 
> coordinate trimming across a 3 corners, the amount you are able to 
> trim may be sharply limited.  It's important to understand, though, 
> that if you trim different amounts from the different corners, the 
> time correlation between the corners will be lost.  Strictly speaking,

> that's not a problem, as time 0 in an IBIS simulation is arbitrary.
> HOWEVER - if users of the model simulate the [Min] and [Typ] cases and

> overlay the results, they will draw incorrect conclusions if they
assume the curves are time-correlated.
> 
> It probably goes without saying, but - you can trim any amount of dead

> time you want off the END of a curve once the slope is zero.  Good 
> practice says the last two points should form a line with zero slope, 
> so that any extrapolation the simulator performs does what you expect.
> 
> As in all modeling - knowing what you've got is the first step in 
> understanding what conclusions you can draw.
> 
> Arpad & others - please correct me if I've gotten any of this wrong
...
> 
> Todd.
> 
> Todd Westerhoff
> VP, Software Products
> SiSoft
> 6 Clock Tower Place, Suite 250
> Maynard, MA  01754
> (978) 461-0449 x24
> twesterh@sisoft.com
> www.sisoft.com
> -----Original Message-----
> From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org] On 
> Behalf Of Dimitry Eisenshtat
> Sent: Saturday, January 13, 2007 3:58 AM
> To: Todd Westerhoff
> Cc: ibis@eda-stds.org; ibis-users@eda.org
> Subject: Re: [IBIS-Users] RE: [IBIS] Ibis open drain strange behaviour
> 
> Todd,
> ok, we understand that time correlation between IBIS and HSpice is not

> guaranteed, but is it really problem? I mean, in the most often 
> situation there is no place for such comparison at all, because you 
> have only IBIS model, no spice netlist is available. This is the first

> reason for making IBIS (if simulator speed is not an issue), is it 
> right? Lets say, I'm with semiconductor vendor side, I have the 
> netlist of the buffer, I  make the IBIS model based on spice 
> simulations, not lab measurements, so on final step when the model is 
> ready I like to check it vs. original spice behavioral. This is the 
> only situation I agree the comparison is important. But in such case 
> there is no REAL problem - I know exactly about the delay, and if it 
> is the only difference between the IBIS & spice - I don't care.
> 
> I want ask you about IBIS simulator aspect of the point we are talking

> about. Look, I find in "Cookbook for ver4" strongly recommendation to 
> trim IBIS model time tables at least to half of max buffer frequency 
> period. (http://www.vhdl.org/pub/ibis/cookbook/cookbook-v4.pdf page 
> 70,
> 5.4.2 V-T Table Windowing). Can you please prefer from simulator 
> software side - is it really problem for the simulator if the time 
> table window is more then such time interval? And one additional 
> point, you wrote "There are specific restrictions on how the dead time

> may be trimmed, which is a longer discussion" - right now I writes 
> perl script which will trim tables in order to leave only transition 
> region and decrease the time window as the Cookbook recommends to do.
> So, can you please explain about these restrictions?
> 
> Thanks,
>   Dmitry
> 
> ... (previous thread clipped)
> 
> 


--
  +---------------------------------------------------------+
  | Dmitry Aizenshtat         Circuit Design Engineer, NSTA |
  | Tel : 972-9-9702-020               Fax : 972-9-9702-001 |
  | mailto:dimita@taux01.nsc.com                            |
  +---------------------------------------------------------+


========================================================================
===================
The privileged confidential information contained in this email is
intended for use only by the addressees as indicated by the original
sender of this email. If you are not the addressee indicated in this
email or are not responsible for delivery of the email to such  a
person, please kindly reply to the sender indicating this fact and
delete all copies of it from your computer and network server
immediately. Your cooperation is highly appreciated. It is advised that
any unauthorized use of confidential information of Winbond is strictly
prohibited; and any information in this email irrelevant to the official
business of Winbond shall be deemed as neither given nor endorsed by
Winbond.

--
This message has been scanned for viruses and dangerous content by
MailScanner, and is believed to be clean.


--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993
Received on Wed Nov 28 20:13:24 2007

This archive was generated by hypermail 2.1.8 : Wed Nov 28 2007 - 20:15:25 PST