Subject: RE: [IBIS-Users] (lv)pecl
From: erik.van.der.ven@philips.com
Date: Tue May 13 2003 - 01:49:50 PDT
As Tom and Fred suggest I have to add "some" resistance to the clamp
diodes to prevent high currents. Must these device models be characterised
or should I just add an arbitrary value. If so what will be the value of
this information. I still don't have the insight what an IBIS simulator
does do with the clamping info?
With kind regards,
Ir. Erik van der Ven
Room DB1032
Business Line Networking Infrastructure
Philips Semiconductors BV
Gerstweg 2
6534 AE Nijmegen
The Netherlands
Phone: +31-24-3534334
"Tom Dagostino" <tom@teraspeed.com>
05/12/03 06:41 PM
Please respond to tom
To: Erik van der Ven/NYM/SC/PHILIPS@EMEA2
<ibis-users@server.eda.org>
cc:
Subject: RE: [IBIS-Users] (lv)pecl
Classification:
Erik
Fred is right that for an ECL model that the voltage range that has to be
characterized is over the 0 to Vcc - 2V range in the table. I like to see
at least the active region between 0 and Vcc modeled. There are some ECL
parts that will not be adequately characterized by only going from 0 to
Vcc - 2V. If I remember correctly ON Semi makes some ECL line drivers
that have about twice the swing of normal ECL.
Fred, the garbage Erik referred to was multiple lines in the tables that
have the same voltage values and zero current. I've seen models with
this before but I don't remember the cause of it.
Yes, IBIS likely goes too far into the clamp regions for characterization.
If your clamp currents are extreme it is likely that the clamp diodes
have not been properly characterized in their SPICE models. If you are
seeing more than a few amperes in the clamps you can assume the intrinsic
resistance of the diodes, the metal, etc. have not been fully
characterized. To eliminate this try adding a few hundred milli Ohms in
series with the clamps to bring the currents down to a more realistic
level.
Tom Dagostino
Teraspeed Consulting Group LLC Teraspeed Consulting Group LLC
2926 SE Yamhill St. Device Modeling Division
Portland, OR 97214 13610 SW Harness Lane
Beaverton, OR 97008
http://www.teraspeed.com 503-430-1065
tom@teraspeed.com
-----Original Message-----
From: owner-ibis-users@server.eda.org [mailto:owner-ibis-users@server.eda.org]On Behalf Of erik.van.der.ven@philips.com
Sent: Monday, May 12, 2003 1:44 AM
To: ibis-users@server.eda.org
Subject: Re: [IBIS-Users] (lv)pecl
Dear Fred,
Thank you for your reply. About the garbage; I explained it in an email I
just sent (directed to Tom).
The s2ibis program does not generate IV- tables from 0-2.2V, but the
program that has been modified by my collegue does do this (apart from the
"garbage" that both programs produce).
Is this range enough? According to Tom it should be -3.3-6.6V. Where is
this range for ECL/PECL defined? I cannot find it in the specification.
When the voltage is out of the normal operating range the currents can be
very high, even so high that the transistor models are not valid anymore.
What is the use of specifying these currents? Can they be left out? If
not, what is done with this information.
I have the same question for the clamp currents. The output can be
disabled, so this is a kind of tri-state (not really high impedant). Also
here the currents are unrealistically high. What is done with this
information? Why must it be specified? The PECL voltage swing is such that
even a fully reflected signal will not cause the output to be outside the
supply range.
With kind regards,
Ir. Erik van der Ven
Room DB1032
Business Line Networking Infrastructure
Philips Semiconductors BV
Gerstweg 2
6534 AE Nijmegen
The Netherlands
Phone: +31-24-3534334
Fred Balistreri <fred@apsimtech.com>
Sent by:
fred@interjet.apsimtech.com
05/09/03 07:10 PM
To: Erik van der Ven/NYM/SC/PHILIPS@EMEA2
cc:
Subject: Re: [IBIS-Users] (lv)pecl
Classification:
Erik, you need to define what convention you are
using when you say voltage range. Remember that
for ECL and PECL both the pullup and pulldown
reference is the same. If the voltage range
you refer to is the IBIS Vtable then your
range is not correct. Under the IBIS conventions
for ECL or PECL type Vtable= Vcc - Vout.
This is true for both pullup/pulldown for PECL/ECL.
IBIS further explains that for ECL, PECL the
range should be VCC - 2.2 volts. Under the
IBIS rules then the range should always be
0 - 2.2 volts for both pullup and pulldown.
Note that 0 really means 3.3 at the output
for your case and 2.2 really means 1.1 at the
output.
I don't quite understand your problem. You state
garbage. It's probably not quite descriptive
enough to understand your issue. Although the
meaning is clear.
Best Regards,
erik.van.der.ven@philips.com wrote:
>
> Part 1.1Type: Plain Text (text/plain)
-- Fred Balistreri fred@apsimtech.com|------------------------------------------------------------------ |For help or to subscribe/unsubscribe, email majordomo@eda.org |with just the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or email a written request to ibis-request@eda.org. | |IBIS reflector archives exist under: | | http://www.eda.org/pub/ibis/email_archive/ Recent | http://www.eda.org/pub/ibis/users_archive/ Recent | http://www.eda.org/pub/ibis/email/ E-mail since 1993
This archive was generated by hypermail 2b28 : Tue May 13 2003 - 09:22:11 PDT