[IBIS-Users] PullUp/PullDown toggle?

Hello,

In some of my models the pullup/pulldown curves end up by toggling +/- 
10mA. It is not of much actual consequence, but estethically foul. An 
example follows below.

I get the same result with s2ibis3 and one other independent tool (also 
using HSpice for simulation), so I suspect this is really in the HSpice 
result files. Has anyone seen something similar before?


   2.40    -12.7710mA        -7.5000mA           -21.3261mA
   2.46    -12.8090mA        -8.0000mA           -21.3770mA
   2.52    -12.8400mA        -7.0000mA           -21.4280mA
   2.58    -12.9000mA        -7.0000mA           -21.4810mA
   2.64    -13.0000mA        -7.0000mA           -21.5310mA
   2.70    -13.0000mA        -8.0000mA           -21.5800mA
   2.76    -13.0000mA        -8.0000mA           -21.6300mA
   2.82    -13.0000mA        -10.0000mA          -22.0000mA
   2.88    -13.0000mA        0.0A                -22.0000mA
   2.94    -10.0000mA        -10.0000mA          -22.0000mA
   3.00    -10.0000mA        -10.0000mA          -22.0000mA
   3.06    -20.0000mA        -10.0000mA          -20.0000mA
   3.12    -20.0000mA        0.0A                -20.0000mA
   3.18    -10.0000mA        -10.0000mA          -30.0000mA
   3.24    -10.0000mA        -10.0000mA          -20.0000mA
   3.30    -10.0000mA        -10.0000mA          -20.0000mA
   3.36    -10.0000mA        -10.0000mA          -30.0000mA
   3.42    -20.0000mA        0.0A                -20.0000mA
   3.48    -20.0000mA        -10.0000mA          -20.0000mA
   3.54    -10.0000mA        -10.0000mA          -30.0000mA
   3.60    -10.0000mA        -10.0000mA          -20.0000mA



Best regards,  Lars Snith
-- 
Those who can, Do
Those who can't, Simulate

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.

--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993