Re: [SI-LIST] : IBIS Subcommittee Formed to Review Spice to IBIS

Hi all,
 
  At the risk of repeating myself there are several very good
reasons to limit the number of points in the IV and VT tables.
e.g. disk size, transfer time, overall accuracy improvement.

The last one may surprise you but I do feel that including for
example a 3rd VT table buys more than increasing the number of points
for most models.

I do agree the number of points could be increased to say 256 to
pick yet another arbitrary spot on the wall. I would prefer to
see a model creator like Arpad propose a new limit based on
actual demonstrated requirements where some form of data reduction is
used.

I feel we should keep this number as small as we can and still create
accurate models to insure the files sizes and download times are reasonable.

I think the biggest problem here is spice to ibis. People are always
generating models with the maximum number of points. I see many many models
that will work EXACTLY the same with 1/3 this many points if they are placed
sensibly instead of using a linear spread.

I am worried that if we set the limit at 1000 we will have all the new
models with 1000 points......
Just doesn't make sense to me sorry... especially with more and more
VT tables being used.
best wishes...
Kellee

At 05:00 PM 6/8/99 -0700, Scott McMorrow wrote:
>I second Jon's opinon.
>
>There is no real reason to limit the number of points in
>IV or VT tables. I have often used a simulator which allows
>an arbitrary number of points over 100 to create high
>resolution simulations. 256 to 512 is often useful to
>capture rising edge timing information accurate to 1ps, along
>with driver overshoot behavior to within 1 mv of HSpice
>simulations.
>
>Model size makes no difference to me. It is the result that

>matters.
>
>Scott McMorrow
>SiQual
>
>jonp@pacbell.net wrote:
>
>> I agree with Weston.
>>
>> Either that or remove the quite artificial limit of number of points in
an IBIS
>> file.
>> I have actually been faced with the problem that even with software to
remove
>> extra points I cannot
>> create IBIS models to the accuracy that I desire with the 100 point
limitation.
>>
>> jon powell
>> Viewlogic Consulting Services
>>
>> Beal, Weston wrote:
>>
>> > Kellee,
>> >
>> > You're disagreeing a mute point. Your point was the same point I was
trying
>> > to state by saying, "the IBIS creator tool should have an algorithm to
>> > remove points in linear regions." We should delete all these extra data
>> > points. The problem that s2ibis has now is that all points are equal
>> > difference. They should be closer in knee points and very sparse is
linear
>> > regions. The IBIS creator tool should have an algorithm to clean out
extra
>> > data.
>> >
>> > So, I agree with you and now you can agree with me.
>> >
>> > Later,
>> > Weston Beal
>> > Signal Integrity Engineer
>> > Compaq Computer Corp.
>> >
>> > -----Original Message-----
>> > From: Kellee Crisafulli [mailto:kellee@hyperlynx.com]
>> > Sent: Monday, 07 June, 1999 2:19 PM
>> > To: Beal, Weston; ibis@eda.org
>> > Subject: RE: [SI-LIST] : IBIS Subcommittee
Formed to
>> > Review Spice to IBIS
>> >
>> > Hi
>> >
>> > I have a comment on Weston's comment on the number of
data
>> > points.
>> > I disagree on one point. Instead of increasing the
number
>> > of points generated
>> > in the IBIS file the spice to IBIS tool should improve
the
>> > quality of the
>> > points
>> > choosen.
>> >
>> > I can hand build files with 50 points that out perform
files
>> > with 400 points.
>> > The big gain is that the FILE SIZE is reduced with higher
>> > accuracy.
>> > Large IBIS files will take up many megabytes on 1000's of
>> > hard drives.
>> > The V/I and V/T tables are the largest part of IBIS
files.
>> > Increasing them 4 x will generally increase the file
size 3
>> > x or more.
>> >
>> > >The third thing that I changed was the number of
points in
>> > the time
>> > >waveforms from 50 to 101. I have to remove one point to
>> > comply with the
>> > >golden parser, but I get better detail. On the issue of
>> > number of points in

>> > >a curve or waveform, I think the user should be able to
>> > define any degree of
>> > >granularity and the IBIS creator tool should have an
>> > algorithm to remove
>> > >points in linear regions. If the resulting curve
still has
>> > too many points,
>> > >then increase the linearity tolerance and try it again.
>> >
>> > Best wishes...
>> > Kellee
>
---------------------------------------------------------
Have a great day....
Kellee Crisafulli
HyperLynx, a division of Pads Software Inc.
SI,EMC,X-talk and IBIS tools for the Windows platform
E-mail: <mailto:kellee@hyperlynx.com>
web:   <http://www.hyperlynx.com>
---------------------------------------------------------
Received on Tue Jun 8 21:20:06 1999