RE: [IBIS] RE: [IBIS-Users] Query reg. USB1.1 IBIS model generation

From: Vivek kumar Singh <Vivekkumar.Singh_at_.....>
Date: Mon Jan 21 2008 - 23:26:48 PST
Hi Arpad,

     For both low and high speed usb, I generated IBIS models with
R_fixture of 50 Ohms. 

 

Mine is USB1.1.  I then did correlation with spice model. Full speed was
matching, but Low speed is not matching with spice.

 

2 queries I have :

   1) In Low speed design, I have slew correcting feedback capacitors.
So, while generating IBIS should I take care of it separately or IBIS
will handle it? 

   

   2) For USB1.1, 45 Ohm R_fixture is used. So, while validating should
I use TLINE also of 45 Ohm? What changes should I make?

 

Regards,

Vivek

 

________________________________

From: owner-ibis@eda.org [mailto:owner-ibis@eda.org] On Behalf Of
Muranyi, Arpad
Sent: Monday, January 21, 2008 10:07 PM
To: ibis-users@eda.org; ibis@eda.org
Subject: [IBIS] RE: [IBIS-Users] Query reg. USB1.1 IBIS model generation

 

Vivek,

 

R_fixture has nothing to do with the 1.5k or 15k resistors.

Select a value for R_fixture that matches the transmission

line impedance.  In the USB case it would be 45 Ohms (single

ended) if my memory serves me right.

 

I would also suggest that you look at the IBIS Cookbook for

help.  There are a lot of good ideas in there.

 

http://www.vhdl.org/pub/ibis/cookbook/cookbook-v4.pdf

 

Arpad

=============================================================

 

________________________________

From: owner-ibis-users@server.eda.org
[mailto:owner-ibis-users@server.eda.org] On Behalf Of Vivek kumar Singh
Sent: Sunday, January 20, 2008 10:34 PM
To: ibis-users@server.eda.org; ibis@server.eda.org
Cc: Vijaya kumar Vinukonda
Subject: [IBIS-Users] Query reg. USB1.1 IBIS model generation

Hi All,

    I'm having problem with ibis model generation for USB1.1 . 

I have following 3 queries :

 

since USB operates in Upstream and Downstream applications with pullup
and pulldown resistors 1.5k and 15k Ohm respectively. Will it have any
effect on choosing R_fixture value for IBIS VT data generation ????

 

What actually we take the value of R_fixture for USB1.1 ?

 

Can someone elaborate on setup for Ibis model generation for USB1.1.

 

 

Regards,

Vivek

-- 

IMPORTANT NOTICE: The contents of this email and any attachments are
confidential and may also be privileged. If you are not the intended
recipient, please notify the sender immediately and do not disclose the
contents to any other person, use it for any purpose, or store or copy
the information in any medium.  Thank you.


-- 
This message has been scanned for viruses and 
dangerous content by MailScanner <http://www.mailscanner.info/> , and is

believed to be clean. 


-- 
This message has been scanned for viruses and 
dangerous content by MailScanner <http://www.mailscanner.info/> , and is

believed to be clean. 

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993
Received on Tue Jan 22 00:04:02 2008

This archive was generated by hypermail 2.1.8 : Tue Jan 22 2008 - 00:05:27 PST