Vivek, By using s2ibis3, I generated three pullup/pulldown I-V curves(max/typ/min), and I used Hspice to run simulation for spice netlist and ibis model. Then, the result show there is very good correlation, but only on typical corner. For max/min corner, I believe there still are some problems cause curves different. Best Regards, Eric Hsu Interface Technologies NetLogic Microsystems, Inc. 1875 Charleston Rd. Mountain View, CA 94043 650-961-6676 x198 This e-mail contains NetLogic Microsystems, Inc. Confidential information -----Original Message----- From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org]On Behalf Of Vivek Kumar Sundriyal Sent: Wednesday, September 21, 2005 8:15 PM To: Sanjay Mehta Cc: ibis@eda.org; ibis-users@eda.org; owner-ibis-users@eda.org Subject: Re: [IBIS-Users] S2IBIS code compiling in Linux Sanjay , This is a problem that I too had faced when I used to use s2ibis2 on linux. To get over this problem, you need to make some slight changes in the source code of s2ibis2. It then works fine. But , Is there any specific reason you need to work on s2ibis2 ? I suggest you to move to s2ibis3, which is in Java and hence OS independent. I observed that the results of the Pullup/Pulldown results are better in s2ibis3. Download the latest s2ibis3 and try working on that. Cheers , Vivek "Sanjay Mehta" <sanjay.mehta@xil To: ibis-users@eda.org, ibis@eda.org inx.com> cc: Sent by: Subject: [IBIS-Users] S2IBIS code compiling in Linux owner-ibis-users@ eda.org 09/22/05 12:07 AM Hi, I have been trying to compile the linux version of the S2IBIS code that is posted on the IBIS website. The code compiles without any errors (I am using Redhat Enterprise Linux WS 3). Unfortunately, I am having problems in getting the correct V-t tables when I use this script. Upon execution of the binary s2ibis, the IBIS model is generated; however, the V-T table is incorrect. The problem seems to be the following: In the *.sp files that the are created with the S2IBIS script, which generate the V-T curves (i.e. a00io.sp, a01io.sp....z00io.sp, z01io.sp) there is a line that states... RFIXS2I dum13806 dum13806 50 Normally, this line should read RFIXS2I pin dum13806 50 --> where "pin" is the IO pad that is being swept for the I-V and connected to the R-fixture for the V-T. Unfortunately, I cannot run the default executable on the website as I am using a special in-house version of HSPICE and so I have recompile the code with the correct addition of the HSPICE command line. If there is anyone who has been successful at compiling in Linux and have some suggestions, please let me know. Thank you. Sanjay Mehta Xilinx, Inc. |------------------------------------------------------------------ |For help or to subscribe/unsubscribe, email majordomo@eda.org |with just the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or email a written request to ibis-request@eda.org. | |IBIS reflector archives exist under: | | http://www.eda.org/pub/ibis/email_archive/ Recent | http://www.eda.org/pub/ibis/users_archive/ Recent | http://www.eda.org/pub/ibis/email/ E-mail since 1993 |------------------------------------------------------------------ |For help or to subscribe/unsubscribe, email majordomo@eda.org |with just the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or email a written request to ibis-request@eda.org. | |IBIS reflector archives exist under: | | http://www.eda.org/pub/ibis/email_archive/ Recent | http://www.eda.org/pub/ibis/users_archive/ Recent | http://www.eda.org/pub/ibis/email/ E-mail since 1993 |------------------------------------------------------------------ |For help or to subscribe/unsubscribe, email majordomo@eda.org |with just the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or email a written request to ibis-request@eda.org. | |IBIS reflector archives exist under: | | http://www.eda.org/pub/ibis/email_archive/ Recent | http://www.eda.org/pub/ibis/users_archive/ Recent | http://www.eda.org/pub/ibis/email/ E-mail since 1993Received on Thu Sep 22 10:57:42 2005
This archive was generated by hypermail 2.1.8 : Thu Sep 22 2005 - 10:59:10 PDT