All, I'm going to jump in the middle here, even though I didn't have the time to read this thread as thoroughly as I would have like. I'm confused by what Akhilesh is describing. Akhilesh, are you saying your driver can't drive the receiver's input pin beyond the VIL and VIH thresholds? If that is truly the case, then you need to consider the datasheet specifications for your receiving device very carefully. It's not a matter of what thresholds you have in an IBIS models you received (they may not be correct), nor is it a matter of what behavior a HSPICE model of the input buffer might exhibit. It's a matter of how the part's performance is specified and guaranteed, and that's in the datasheet. There can be a difference between the thresholds a signal is timed to, and the thresholds that a switching signal must ultimately attain to ensure a valid switching event. Distinguishing between "signal quality" and "signal timing" thresholds in IBIS models can get pretty tricky, even for those of us who've been at it a while. What caught my eye was your initial description of the buffer as a "hysteresis buffer", although I don't know if you meant the driving or receiving device. If you meant the receiving device, it could well be the case that the part is _timed_ to a voltage between the VIL and VIH thresholds, but chances are, the signal still has to _attain_ VIL and VIH thresholds to be valid. The device timing specifications are key to understanding what simulations to perform and how to interpret the results. Hope that helps, Todd. Todd Westerhoff VP, Software Products SiSoft 6 Clock Tower Place, Suite 250 Maynard, MA 01754 (978) 461-0449 x24 twesterh@sisoft.com www.sisoft.com -----Original Message----- From: owner-ibis@eda.org [mailto:owner-ibis@eda.org] On Behalf Of Tom Dagostino Sent: Friday, January 04, 2008 1:02 PM To: 'Muranyi, Arpad'; 'Akhilesh CHANDRA'; ibis@eda-stds.org; owner-ibis-users@eda.org; ibis-users@eda.org Subject: RE: [IBIS-Users] RE: [IBIS] RE: IBIS model behavior between Vinh and Vinl input Arpad I think we are in agreement. I took Akhilesh's comment: IBIS specs don't define that how logic X represent in IBIS simulation, Due to this different simulator give different behavior for X. In my view we will need to define how logic X represent in IBIS model simulation. It will help to align all the simulator results. To mean that he wanted to define X as a 1 or 0. Tom Dagostino Teraspeed(R) Labs 13610 SW Harness Lane Beaverton, OR 97008 503-430-1065 503-430-1285 FAX tom@teraspeed.com www.teraspeed.com Teraspeed Consulting Group LLC 121 North River Drive Narragansett, RI 02882 401-284-1827 -----Original Message----- From: owner-ibis@server.eda.org [mailto:owner-ibis@server.eda.org] On Behalf Of Muranyi, Arpad Sent: Friday, January 04, 2008 9:41 AM To: tom@teraspeed.com; Akhilesh CHANDRA; ibis@server.eda-stds.org; owner-ibis-users@server.eda.org; ibis-users@server.eda.org Subject: RE: [IBIS-Users] RE: [IBIS] RE: IBIS model behavior between Vinh and Vinl input Tom, I may disagree with you on this one. The 1 volt and 0 volt representation of "true" and "false" is just as "unreal" as an "X". None of these are actual waveforms. These are indicators which tells you whether the input signal was below, above, or between Vinh and Vinl. I think it is plain wrong to have a "1" or a "0" on the output of the receiver when the signal is between Vinh and Vinl and it misleads the user of these tools thinking that they have good signal integrity while they have problems. I fully agree that digital parts are not made to operate with waveforms between Vinh and Vinl. Ant that is exactly the reason we should have an output value of "X" to find out when the waveforms are in that region. And that fact that you described that the "actual output ... will change" is exactly the reason for the "X", because we simply don't know what it will be. It is not guaranteed that it will be a "1" or a "0". How do you describe that if not with an "X"? Arpad ======================================================================== ======= -----Original Message----- From: Tom Dagostino [mailto:tom@teraspeed.com] Sent: Friday, January 04, 2008 1:34 AM To: 'Akhilesh CHANDRA'; Muranyi, Arpad; ibis@server.eda-stds.org; owner-ibis-users@server.eda.org; ibis-users@server.eda.org Subject: RE: [IBIS-Users] RE: [IBIS] RE: IBIS model behavior between Vinh and Vinl input ... ... ... But having all simulators default to some arbitrary state when the input is between the reference levels is setting the user up for failure. People tend to assume if the simulator says X, X is real. If they don't see X in the real circuit then there is something wrong. Not all parts will conform to some arbitrarily designated state. Digital parts are not made to operate with their inputs between Vinh and Vinl. Most parts have specifications that state the minimum slew rate (input risetime/falltime) as the input to the part transitions between the two reference levels. The actual output of an input buffer for a given input voltage between Vinl and Vinh will change depending on the internal noise of the IC, the noise on the input, process, temperature, voltage, phase of the moon, crosstalk, etc. Tom Dagostino Teraspeed(R) Labs 13610 SW Harness Lane Beaverton, OR 97008 503-430-1065 503-430-1285 FAX tom@teraspeed.com www.teraspeed.com Teraspeed Consulting Group LLC 121 North River Drive Narragansett, RI 02882 401-284-1827 -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. -------------------------------------------------------------------- |For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org |with the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or e-mail a request to ibis-request@eda-stds.org. | |IBIS reflector archives exist under: | | http://www.eda-stds.org/pub/ibis/email_archive/ Recent | http://www.eda-stds.org/pub/ibis/users_archive/ Recent | http://www.eda-stds.org/pub/ibis/email/ E-mail since 1993 -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. -------------------------------------------------------------------- |For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org |with the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or e-mail a request to ibis-request@eda-stds.org. | |IBIS reflector archives exist under: | | http://www.eda-stds.org/pub/ibis/email_archive/ Recent | http://www.eda-stds.org/pub/ibis/users_archive/ Recent | http://www.eda-stds.org/pub/ibis/email/ E-mail since 1993 -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. -------------------------------------------------------------------- |For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org |with the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or e-mail a request to ibis-request@eda-stds.org. | |IBIS reflector archives exist under: | | http://www.eda-stds.org/pub/ibis/email_archive/ Recent | http://www.eda-stds.org/pub/ibis/users_archive/ Recent | http://www.eda-stds.org/pub/ibis/email/ E-mail since 1993Received on Fri Jan 4 10:28:41 2008
This archive was generated by hypermail 2.1.8 : Fri Jan 04 2008 - 10:28:47 PST