RE: [IBIS] maximum current flows

From: Lynne D. Green <lgreen22_at_.....>
Date: Wed Jun 01 2005 - 19:56:35 PDT
Hello, YY Lau,
	 
Please check the value of RS in your diode model.  This resistance should
never be 0 Ohm.
	 
Perhaps the model maker or chip designer could give you a good estimate of
RS.
	 
- Lynne
	 


________________________________

		From: owner-ibis@eda.org [mailto:owner-ibis@eda.org] On
Behalf Of lau yy
		Sent: Tuesday, May 31, 2005 10:41 PM
		To: ibis@eda.org; ibis-user@eda.org
		Subject: [IBIS] maximum current flows
		
		
		Dear ALL,
		 
		Recently, I have faced the maximumcurrent flows warning. Do
anyone know what actual the main cause?
		 
		I suspect is the R package/ R _pin value that is too small.
I try to replace some larger value 
		and simulate again. I found that the problems gone. Is it
that mean the problem cause by the R?
		 
		Below are the message the shown after use ibischk3.
		 
		WARNING - Model 'A22': Extreme currents present in TYP
GND_Clamp VI Curve 
		(-23.94A @ -1.5V)
		 WARNING - Model 'A22': Extreme currents present in MIN
GND_Clamp VI Curve 
		(-26.24A @ -1.5V)
		 WARNING - Model 'A22': Extreme currents present in MAX
GND_Clamp VI Curve 
		(-22.08A @ -1.5V)
		 WARNING - Model 'OEB': Extreme currents present in TYP
GND_Clamp VI Curve 
		(-15.92A @ -1.5V)
		 WARNING - Model 'OEB': Extreme currents present in MIN
GND_Clamp VI Curve 
		(-17.48A @ -1.5V)
		 WARNING - Model 'OEB': Extreme currents present in MAX
GND_Clamp VI Curve 
		(-14.66A @ -1.5V)
		 WARNING - Model 'CLK': Extreme currents present in TYP
GND_Clamp VI Curve 
		(-3.133e+11A @ -1.5V)
		 WARNING - Model 'CLK': Extreme currents present in MIN
GND_Clamp VI Curve 
		(-4.438e+10A @ -1.5V)
		 WARNING - Model 'CLK': Extreme currents present in MAX
GND_Clamp VI Curve 
		(-3.558e+12A @ -1.5V)
		 
		Any comments on this?
		 
		 
		Rdgs
		YYLAU
	
----------------------------------------------------------------- |For help
or to subscribe/unsubscribe, email majordomo@eda.org |with the appropriate
command message(s) in the body: | | help | subscribe ibis | subscribe
ibis-users | unsubscribe ibis | unsubscribe ibis-users | |or email a request
to ibis-request@eda.org. | |IBIS reflector archives exist under: | |
http://www.eda.org/pub/ibis/email_archive/ Recent |
http://www.eda.org/pub/ibis/users_archive/ Recent |
http://www.eda.org/pub/ibis/email/ E-mail since 1993 



-----------------------------------------------------------------
|For help or to subscribe/unsubscribe, email majordomo@eda.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or email a request to ibis-request@eda.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda.org/pub/ibis/email_archive/  Recent
|  http://www.eda.org/pub/ibis/users_archive/  Recent
|  http://www.eda.org/pub/ibis/email/          E-mail since 1993
Received on Wed Jun 1 19:57:25 2005

This archive was generated by hypermail 2.1.8 : Wed Jun 01 2005 - 19:57:44 PDT