RE: [IBIS-Users] [Model Selector] and C_comp

From: Muranyi, Arpad <Arpad_Muranyi@mentor.com>
Date: Wed Jun 29 2011 - 11:22:15 PDT

Lars,

Both [Add Submodel] and [Driver Schedule] would retain
the C_comp in the paralleled [Model]s, but I don't think
they would do what you need in the paralleled [Model]s.
I can't think of anything else in IBIS that puts multiple
[Model]s on the same pad.

You could perhaps make two [Model]s on two different pads,
and "short" them together with a [R Series] using a low
resistance value.

I hope this gives you some ideas to solve your problem...

Arpad
===========================================================

-----Original Message-----
From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org] On Behalf Of Lars Snith
Sent: Wednesday, June 29, 2011 7:27 AM
To: ibis-users
Subject: [IBIS-Users] [Model Selector] and C_comp

Hello Folks,

For pads with controllable slewrate the [Model Selector] keyword is a
nice solution when one want to include the complete set of options.

However, consider two separate pads of very different function, bonded
to the same pin. Using [Model Selector] will for sure take care of the
functionality, but in this case the C_comp of both pads should actually
be summed up.

I can of course make models of each parallel configuration, but possibly
there is a neater solution?

Best regards, Lars Snith

-- 
Those who can, Do
Those who can't, Simulate
-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993
-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
--------------------------------------------------------------------
|For help or to subscribe/unsubscribe, e-mail majordomo@eda-stds.org
|with the appropriate command message(s) in the body:
|
|  help
|  subscribe   ibis       <optional e-mail address, if different>
|  subscribe   ibis-users <optional e-mail address, if different>
|  unsubscribe ibis       <optional e-mail address, if different>
|  unsubscribe ibis-users <optional e-mail address, if different>
|
|or e-mail a request to ibis-request@eda-stds.org.
|
|IBIS reflector archives exist under:
|
|  http://www.eda-stds.org/pub/ibis/email_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/users_archive/ Recent
|  http://www.eda-stds.org/pub/ibis/email/         E-mail since 1993
Received on Wed Jun 29 11:22:50 2011

This archive was generated by hypermail 2.1.8 : Wed Jun 29 2011 - 11:23:29 PDT