Message strings from ibischk3 V3.2.6 that appear to be problem notifications:

%s %s Value Cannot Be 'NA' for %s Beginning at Line %d
%s %s data is non-monotonic
%s %s: %s has Decreasing Current
%s %s: %s has Increasing Current
%s '%s': %s %s Ramptime %5.3ensec unusually large ( > %5.3ensec )
%s : Typ is not in between Min and Max for Model Spec defined on line %d
%s Already Defined
%s Not Defined For %s Waveform Beginning on Line %d
%s Not Defined For Ramp Beginning on Line %d
%s Over %s Characters Long
%s Pin Subparameter Must Be '%s'
%s and %s cannot be specified together
%s is an invalid Pin_Mapping column entry.
%s is greater than zero for Model Spec defined on line %d
%s is greater than zero for Sub Model Spec defined on line %d
%s is less than zero
%s is less than zero for Model Spec defined on line %d
%s is less than zero for Sub Model Spec defined on line %d
%s keyword column count must be %d or %d, found %d columns.
%s must be greater than 0 in a Ramp specification
%s requires %s to be specified for Model Spec defined on line %d
%s specified after beginning of timing data
%s string '%s' is too long, truncating to %u characters.
%s(%s) is not greater than %s(%s) for Model Spec defined on line %d
%s(%s) is not greater than or equal to %s(%s) for Model Spec defined on line %d
%s(%s) is not less than %s(%s) for Model Spec defined on line %d
%s(%s) is not less than or equal to %s(%s) for Model Spec defined on line %d
'%s' Definition Missing '%s' Data
'%s' Subparameter Missing %s
'%s' column header not found or out of order.
'%s' is the name of a Model and a Model Selector
'Driver Schedule' Missing model Name
'IBIS Ver' Keyword Not First In File
'Model Selector' Keyword Missing name
'Model' Keyword Missing name
'NA' Not Allowed For Typical Value
'Pin' Keyword Missing Data For Component '%s'
'Ramp' Keyword Not Defined For Model '%s'
'Sub Model' Keyword Missing name
'Voltage Range' Keyword Not Defined For Model '%s'
'signal_name' column header not found.
6 Line Items Not Allowed For These Pin Definitions
A new Pin %s has been defined before terminating a previous Fork with the corresponding Endfork
Add Submodel Mode not found
Add Submodel Name Over %d Characters Long
Add Submodel Name not found
Add Submodel is not allowed for Series or Series_switch models
All %s Hystereis Thresholds should be specified for Model Spec defined on line %d
At least two delays must be specified
Bad line type passed to hdr.
Bandwidth <%u> must be less than Number_of_Pins <%u>.
Bandwidth for this Banded, circle-back matrix exceeds the limit of %u.
Bandwidth only allowed for Banded Matrices
Blank Number_of_Pins value.
Blank Number_of_Sections value.
C should not be less than zero
CMPT '%s', Pin '%s': Pin Capacitance %gpF greater than %gpF
CMPT '%s', Pin '%s': Pin Inductance %gnH greater than %gnH
CMPT '%s', Pin '%s': Pin Resistance %g Ohms greater than %g Ohms
CMPT '%s': Cpkg %s value %gpF not within expected range (%gpF, %gpF)
CMPT '%s': Cpkg Max value < Min value
CMPT '%s': Lpkg %s value %gnH not within expected range (%gnH, %gnH)
CMPT '%s': Lpkg Max value < Min value
CMPT '%s': Rpkg %s value %g Ohms not within expected range (%g Ohms, %g Ohms)
CMPT '%s': Rpkg Max value < Min value
Cannot Nest Forks
Capacitance matrix not found for Package Model '%s'.
Capacitance_Matrix cannot be specified when Number_Of_Sections is specified for Package Model %s.
Component '%s' contains a blank character.
Component '%s' is duplicated within the .ibs file.
Component '%s': Diff_Pin '%s' is not unique.
Component '%s': Diff_Pin '%s' not previously declared in Pin section.
Component '%s': Diff_pin '%s' already in use as an inv_pin.
Component '%s': Inv_pin '%s' already in use as a Diff_pin.
Component '%s': Model '%s' for Pin '%s' not defined.
Component '%s': Pin '%s' not referenced in Pin Mappings.
Component '%s': Pin Mapping '%s': gnd_clamp_ref entry is usually connected to GND.
Component '%s': Pin Mapping '%s': power_clamp_ref entry is usually connected to POWER.
Component '%s': Pin Mapping '%s': pulldown_ref entry is usually connected to GND.
Component '%s': Pin Mapping '%s': pullup_ref entry is usually connected to POWER.
Component '%s': Pin Mapping Pin '%s' not previously declared in Pin section.
Component '%s': Pin Mapping gnd_clamp_ref entry '%s' is not connected to at least one pin whose model_name is POWER or GND.
Component '%s': Pin Mapping power_clamp_ref entry '%s' is not connected to at least one pin whose model_name is POWER or GND.
Component '%s': Pin Mapping pulldown_ref entry '%s' is not connected to at least one pin whose model_name is POWER or GND.
Component '%s': Pin Mapping pullup_ref entry '%s' is not connected to at least one pin whose model_name is POWER or GND.
Component '%s': [Series Pin Mapping] Model '%s' is not defined.
Component '%s': [Series Pin Mapping] Model '%s' is not of type Series.
Component '%s': [Series Pin Mapping] Model '%s' is not of type Series_Switch.
Component '%s': [Series Pin Mapping] Model '%s' is of type Series so function_table_group '%s' is ignored.
Component '%s': [Series Pin Mapping] Model '%s' is of type Series_Switch so function_table_group is required.
Component '%s': [Series Pin Mapping] Model '%s' is of unknown type.
Component '%s': [Series Pin Mapping] Pin1 '%s' has Model '%s' with unknown type.
Component '%s': [Series Pin Mapping] Pin1 '%s' has an unknown model.
Component '%s': [Series Pin Mapping] Pin1 '%s' not previously declared in Pin section.
Component '%s': [Series Pin Mapping] Pin1 '%s': model type cannot be Series or Series_switch.
Component '%s': [Series Pin Mapping] Pin2 '%s' has Model '%s' with unknown type.
Component '%s': [Series Pin Mapping] Pin2 '%s' has an unknown model.
Component '%s': [Series Pin Mapping] Pin2 '%s' not previously declared in Pin section.
Component '%s': [Series Pin Mapping] Pin2 '%s': model type cannot be Series or Series_switch.
Component '%s': [Series Pin Mapping] defined but [Pins] not defined.
Component '%s': inv_pin '%s' is not unique.
Component '%s': inv_pin '%s' not previously declared in Pin section.
Component name '%s' too long. Will be truncated
Component: %s Series Switch Function '%s' is used but not defined
Could not find definition for Submodel %s of Model %s
Define_Package_Model '%s' is duplicated within the .ibs file.
Description keyword not found for Package Model '%s'.
Detected an orphan 'Node' sub param
Detected previous unterminated Forks
Detected the start of an orphan 'Endfork'
Detected the start of an orphan 'Fork'
Detected the start of an orphan 'NC'
Detected the start of an orphan R/L/C section
Diff_Pin column pin same as inv_pin column pin.
Diff_Pin data line column count must be 4 or 6.
Driver Schedule: Already Defined for this model
Driving mode is not valid for input model types
Duplicate C sub param in R/L/C section
Duplicate C_pkg sub-parameter.
Duplicate Capacitance Matrix.
Duplicate Copyright keyword.
Duplicate Date keyword.
Duplicate Diff_Pin keyword found.
Duplicate File_Rev keyword.
Duplicate File_name keyword.
Duplicate IBIS_Ver keyword
Duplicate IBIS_Ver keyword.
Duplicate Inductance Matrix.
Duplicate L sub param in R/L/C section
Duplicate L_pkg sub-parameter.
Duplicate Len sub param in R/L/C section
Duplicate Notes keyword.
Duplicate Number_of_Pins keyword.
Duplicate Number_of_Sections keyword.
Duplicate Package keyword.
Duplicate Path_Description '%s'
Duplicate Pin '%s'.
Duplicate Pin Mapping Pin.
Duplicate Pin keyword found.
Duplicate Pin_Mapping keyword found.
Duplicate R sub param in R/L/C section
Duplicate R_pkg sub-parameter.
Duplicate Reference Designator '%s'
Duplicate Resistance Matrix.
Duplicate Row column index %u.
Duplicate Series switch Group name '%s'
Duplicate Series_Pin_Mapping keyword found.
Duplicate Source keyword.
Duplicate [Number of Pins] keyword
Duplicate [Pin List] keyword found.
Duplicate [Series_Switch_Groups] keyword found.
Duplicate column header '%s' .
Duplicate definition for %s %s
EBD Model '%s' has no paths defined
ERROR (line %*lu) - IBIS Version Cannot Be Determined.  Exiting.
Each line of Pin data must contain either 3 or 6 columns.
Ebd Model keyword 'Begin_Board_Description' not found or blank.
Ebd file '%s' recursively references the component %s in the calling Ebd file '%s'
Empty Fork/Endfork found
Empty R/L/C section found
End_Model_Data cannot be specified when Number_Of_Sections is specified for package %s.
Endfork found without enclosing Fork
Error parsing R/L/C section. Missing '='
Exceeds 80 chararacters.
Excessive data <%s>, only Index and Value should be specified for a Sparse_matrix.
Expected %d columns in Package sub-parameter line, found %d columns.
Expected %u Rows, found %u for Matrix ending previous to this line.
Expected %u columns of Row data for [Row] %s in Matrix ending previous to this line, found %u column%c.
Expected Pin <%s> at matrix row index %u, found at matrix row index %u.
Expected at least one column of Row data for [Row] %s in Matrix ending previous to this line.
Extraneous data on '%s' line.
File Name Requires '.ebd' Extension.
File Name Requires '.ibs' Extension.
File Name Requires '.pkg' Extension.
File name '%s' too long. Will be truncated
File name ("%s") Does Not Match Internal Name ("%s")
File name Too Long
File name opened '%s' not the same as File_name '%s'.
File_name '%s' contains a character '%c' that is illegal for DOS.
File_name '%s' contains an upper case character '%c'.
File_name '%s' contains more than one period.
File_name '%s' must contain one period.
Filename '%s' should be lowercase
First %s Value should be the same as the Last for %s Waveform Beginning at Line %d
Found a Node '%s' containing '/'. Possible syntax error
Found a Node '%s' containing '='. Possible syntax error
Found a Node '%s'. Possible syntax error
Found a Pin Name '%s' containing '/'. Possible syntax error
Found a Pin Name '%s' containing '='. Possible syntax error
Found a Pin Name '%s'. Possible syntax error
Found illegal character with code %x. Not 7bit ASCII. Converting to space
Found some %s (%s) offsets greater than 0 for Table Beginning at Line %d
Found some %s (%s) offsets less than 0 for Table Beginning at Line %d
IBIS files should not contain tab characters.
IBIS_Version must be first keyword.
Illegal IBIS_Version '%s'.
Illegal use of Reserved Word '%s'.
Inductance matrix not found for Package Model '%s'.
Inductance_Matrix cannot be specified when Number_Of_Sections is specified for Package Model %s.
Invalid Add Submodel Line. Expecting two items only
Invalid Character ("%1.1s") In File name
Invalid Comment Character '%c'.
Invalid Comment Character Definition.
Invalid Node specified. Missing '.'
Invalid Ramp %s Line
Invalid Sub Model Name ("%s"); Reserved Word.
Invalid Submodel Name ("%s"); Reserved Word.
Invalid file name '%s'. It has no extension
Keyword 'Package' not defined for Component '%s'.
Keywords Must Begin In Column 1
L and C must be specified when Len != 0
L should not be less than zero
Len should be specified before C
Len should be specified before L
Len should be specified before R
Len should not be less than zero
Matrix type not specified.
Model %s %s: Found two Series_MOSFETs with identical Vds value %e
Model %s %s: Lc_series cannot be specified if C_series is not specified
Model %s %s: No series data found
Model %s %s: Rc_series cannot be specified if C_series is not specified
Model %s %s: Rl_series cannot be specified if L_series is not specified
Model %s is of type Series_switch. [Off] keyword is required
Model %s is of type Series_switch. [On] keyword is required
Model %s used in the Driver Schedule of Model %s cannot itself have a Driver Schedule
Model %s used in the Driver Schedule of Model %s is not defined
Model %s used in the Driver Schedule of Model %s should be an output model
Model %s: The [%s Waveform] 
Model %s: Vds not specified for [Series MOSFET] defined on line %d
Model %s: Vds should be >= 0 for [Series MOSFET] defined on line %d
Model %s: [Series_MOSFET] is not allowed in conjunction with the [Off] keyword
Model '%s' %s Curve %s With A Typical Value of 'NA'
Model '%s' in Model Selector '%s' is not defined in the file
Model '%s' is of type Series_switch. %s should be defined before the [On] and [Off] sections
Model '%s'. already used in this Model Selector
Model '%s': %s Not Defined
Model '%s': %s Required when No Voltage Range is Specified
Model '%s': %s VI curves cannot drive through Vmeas=%gV
Model '%s': %s is not allowed when Model_type is Series
Model '%s': %s is not allowed when Model_type is Series_switch
Model '%s': %s is set when Model_type is not Terminator
Model '%s': '%s' Curve Requires More Than 1 Entry
Model '%s': C_comp %s value %gpF out of expected range (%gpF, %gpF)  
Model '%s': Cac must be defined when Rac is
Model '%s': Currents <> 0.0mA in 'Pulldown' for Open_source device
Model '%s': Currents <> 0.0mA in 'Pullup' for Open_drain/Open_sink device
Model '%s': Extreme currents present in %s %s VI Curve (%gA @ %gV)
Model '%s': Model_type '%s' must have %s set
Model '%s': Rac must be defined when Cac is
Model '%s': Ramp Not Allowed for Series and Series_switch
Model '%s': Ramp Not Defined
Model '%s': The [Driver_Schedule] has no models defined
Model '%s': The [Driver_Schedule] has only one model defined
Model Descriptor string '%s' is too long, truncating to %u characters.
Model Name '%s' Undefined For Pin '%s'
Model Name ("%s") previously used in this Driver Schedule
Model Name Over %d Characters Long
Model Name Previously Defined ("%s")
Model Name in Driver Schedule is the same as enclosing Model ("%s")
Model Selector Name Over %d Characters Long
Model Selector Name Previously Defined ("%s")
Model Selector Sub-Parameter
Model Selector: '%s' has no models defined
Model Selector: '%s' has only one model defined
Model Spec Sub-Parameter
Model Specification: Already Defined for this model
Model name not found.
Model_Data cannot be specified when Number_Of_Sections is specified for package %s.
More Pin Numbers names than Number of pins.
More than 100 [Series_MOSFET]s are defined
More than 100 data points provided for %s table
No Column Index.
No Component name found
No Diff_Pin column entry.
No Group names specified on this line
No Model specified.
No Pin Name found after Pin sub param
No Pin Numbers names found.
No Pin number.
No Pin1 specified.
No Pin2 specified.
No Pin_name found .
No Reference Designator name found
No file name found
No inv_pin column entry.
No preceding [On] or [Off] keyword found. Assuming [On]
No pulldown_ref data.
No pullup_ref data.
No ref_designatior.pin found after Node sub param
No row data.
No signal_name found
No tdelay_typ column entry.
No vdiff column entry.
Node Pin name string too long. will be truncated.
Node Reference designator string too long. will be truncated.
Non-Comment Line Exists After 'End' Keyword
Non-Driving mode is not valid for output model types
Non-comment line exists after 'End' keyword.
Number of Pins <%u> not the same as count of Pin Numbers names found <%u>.
Number of Pins is zero, unable to add Pin Number.
Number of Sections should be specified before Pin Numbers
Number_of_Pins = 0.
Number_of_Pins keyword not found or value bad for Ebd Model '%s'.
Number_of_Pins keyword not found or value bad for Package Model '%s'.
Number_of_Sections = 0.
OEM keyword not found for Package Model '%s'.
Only %u columns of data allowed for this Row .
Orphan Component keyword.
Orphan Data Line.
Orphan Data line.
Orphan Electrical Board Description keyword.
Orphan File Header keyword.
Orphan Model Selector keyword.
Orphan Model keyword.
Orphan Package Model keyword.
Orphan Sub Model keyword.
Orphan data line keyword.
Orphaned Keyword '%s'.  Needs a '%s'
PIN NUMBER string too long.
POWER Clamp Reference
POWER Pulse Table
Package '%s' Subparameter Not Defined For Component '%s'
Package Model keyword 'Define_Package_Model' not found or blank.
Package Subparameter '%s' Already Defined For Component '%s'
Package sub-parameters must start in column 1.
Path %s or a branch does not terminate after NC
Path Descriptor '%s' has no segments
Pin %s is NC. Should not have any references in Pin Mapping
Pin %s is a GND pin. Usually only has Pulldown_ref in Pin Mapping
Pin %s is a POWER pin. Usually only has Pullup_ref in Pin Mapping
Pin '%s' %s Over 20 Characters Long
Pin '%s' Already Defined
Pin '%s' found in Package_Model '%s' Pin_Numbers list not found in Component '%s' Pin list.
Pin '%s' has %d sections. This is greater than the Number of Sections %d specified
Pin '%s' not found on Component '%s' in file '%s'
Pin '%s' used in Path '%s' not defined
Pin '%s' was not referenced on any Electrical Path
Pin '%s' was referenced %d times on Electrical Paths
Pin '%s' was referenced on Electrical Paths but is implicitly connected to a power or a gnd plane
Pin Mapping data lines must contain either 3 or 5 columns.
Pin Numbers name string too long. will be truncated.
Pin Subparameter '%s' Defined Multiple Times
Pin Subparameter '%s' Is Missing
Pin name string too long. will be truncated.
Premature end of R/L/C section
Pulldown Reference %s is also used as a Pullup Reference
R should not be less than zero
Ramp '%s' Subparameter Not Defined for Model '%s'
Ramp Subparameter '%s' Already Defined For Model '%s'
Reached Maximum Pin Count On Component '%s'
Reference Designator '%s' refers to the Component '%s' itself being defined
Reference Designator '%s' used in Path '%s' not defined
Reference Designator name '%s' too long. Will be truncated
Repeated ROW <%s>.
Require at least 2 Data Points for %s Waveform Beginning at Line %d
Require at least 2 Voltage Points for %s Beginning at Line %d
Required End_Board_Description keyword not found.
Required End_Model_Data keyword not found for package %s.
Required End_Package_Model keyword not found.
Required Model_Data keyword not found for package %s.
Required keyword '%s' not found in file '%s'.
Required keyword 'Component' not found.
Required keyword 'End' not found.
Required keyword 'Manufacturer' not defined for Component '%s'.
Required keyword Pin_List not found.
Required keyword Pin_Numbers not found.
Required sub-parameter C_pkg not found.
Required sub-parameter L_pkg not found.
Required sub-parameter R_pkg not found.
Resistance_Matrix cannot be specified when Number_Of_Sections is specified for Package Model %s.
Series switch Group name '%s' over %d characters long
Series switch Group name cannot be 'On' or 'Off'
Signal name not found.
Some Fork sub parameters were not terminated with Endfork
Sub Model Name Over %d Characters Long
Sub Model Specification: Already Defined for this sub model
SubModel %s: Both Pullup and Pulldown cannot be specified when Off_delay is specified.
SubModel Name Previously Defined ("%s")
Submodel %s: Either [Pullup] or [Pulldown] is required when Submodel_type is Bus_hold
Submodel %s: Empty Submodel Spec
Submodel %s: GND Pulse Table or POWER Pulse Table or GND Clamp or POWER Clamp is required when Submodel_type is Dynamic_clamp
Submodel %s: V_trigger_f (%s) is greater than the start of Falling Waveform
Submodel %s: V_trigger_f (%s) is less than the end of Falling Waveform
Submodel %s: V_trigger_r (%s) is greater than the end of Rising Waveform
Submodel %s: V_trigger_r (%s) is less than the start of Rising Waveform
Submodel %s: [Ramp] is required when Submodel_type is Bus_hold
Submodel %s: [Submodel Spec] Off_delay  cannot be specified with Dynamic_clamp submodels
Submodel %s: [Submodel Spec] V_trigger_f is required when GND_Pulse is specified
Submodel %s: [Submodel Spec] V_trigger_f is required when Submodel_type is Bus_hold
Submodel %s: [Submodel Spec] V_trigger_r is required when POWER_Pulse is specified
Submodel %s: [Submodel Spec] V_trigger_r is required when Submodel_type is Bus_hold
Submodel %s: [Submodel Spec] is required when Submodel_type is Bus_hold
Submodel '%s': %s Not Defined
Suspicious Bandwidth value.
Suspicious Number_of_Pins value.
Suspicious Number_of_Sections value.
TTgnd Max value should be > 0
TTgnd Min value should be > 0
TTgnd Typical value should be > 0
TTpower Max value should be > 0
TTpower Min value should be > 0
TTpower Typical value should be > 0
The %s Matrix is Banded and requires the 'Bandwidth' keyword.
The maximum column must be specified or NA.
The minimum column must be specified or NA.
The typical column must be specified.
Time value did not increase
Too Many Line Items For Keyword COMMENT_CHAR.
Too many Diff Pin data columns.
Typ value is not in between Min and Max 
Unexpected data after signal_name.
Unexpected token '%s' found in R/L/C section
Unknown file extension'%s'. Should be '.ibs' or '.ebd'
Unrecognized data after 'signal_name'
Value %e repeated in the First Column
Vinh should not be specified for model type %s
Vinl should not be specified for model type %s
Voltage Value Cannot Be 'NA'
Waveform with [R_fixture]=%g Ohms and [%s]=%gV has %s column DC endpoints of %5.2fV and %5.2fv, but an equivalent load applied to the model's I-V tables yields
When 5 columns are specified, the headings gnd_clamp_ref and power_clamp_ref must be used.
When using 6 columns, the headers R_pin, L_pin, and C_pin must be listed.
When using 6 columns, the tdelay_min and tdelay_max headers must be used.
[GND Pulse Table] Already Defined
[Model Spec] should be specified immediately after all the subparameters of a model and before the other keywords of a model
[Model] %s has no description of the buffer's high state
[Model] %s has no description of the buffer's low state DC
[POWER Pulse Table] Already Defined
[Row] %s must contain a self-coupled index and entry.
[Series Pin Mapping] Data lines must contain either 3 or 4 columns.
[Series Pin Mapping] When 4 columns are specified, the heading 'function_table_group' must be used.
[Submodel Spec] should be specified before other keywords for a model
