Hi Vivek, I have the following opinion about your problem. 1) For 0.0V as input your typical and maximum current values are significantly higher than they should be. The minimum current value is tolerable. They should be in micro-amps(i.e extremely low...very close to 0.0 A). Hence the errors. 2)You can remove the "Model MODEL1: POWER Clamp : Minimum value never becomes zero WARNING " by simply changing the Minimum current to 0.3000uA from 72.3000uA. Since the current is already in micro-Amperes this change will be quite insignifucant. 3)However you cannot do this to your typ and max curent readings, since such a change will be considered as a significant change. I suggest you go back to your netlist design,source files and check the Power Clamp part once again. Hope this helps. Regards, Nilimp Bhatt -----Original Message----- From: owner-ibis-users@eda.org [mailto:owner-ibis-users@eda.org] On Behalf Of Vivek Kumar Sundriyal Sent: Monday, July 11, 2005 5:40 PM To: ibis-users@eda.org Subject: [IBIS-Users] Warning - "Typical value never becomes zero" Hi , I have developed the IBIS model using s2ibis3 and I am using IBIS version 3.2 When I compile the .ibs file, I get the following warning : WARNING - Model MODEL1: POWER Clamp : Typical value never becomes zero WARNING - Model MODEL1: POWER Clamp : Minimum value never becomes zero WARNING - Model MODEL1: POWER Clamp : Maximum value never becomes zero On looking at the Power clamp data, the current values that I get at 0.0V are : 0.3193mA 72.3000uA 0.6643mA for typ,min and max respectively. Can anyone elaborate on this warning ? And how serious is this ? Cheers , Vivek |------------------------------------------------------------------ |For help or to subscribe/unsubscribe, email majordomo@eda.org with just |the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or email a written request to ibis-request@eda.org. | |IBIS reflector archives exist under: | | http://www.eda.org/pub/ibis/email_archive/ Recent | http://www.eda.org/pub/ibis/users_archive/ Recent | http://www.eda.org/pub/ibis/email/ E-mail since 1993 Confidentiality Notice The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain confidential or privileged information. If you are not the intended recipient, please notify the sender at Wipro or Mailadmin@wipro.com immediately and destroy all copies of this message and any attachments. |------------------------------------------------------------------ |For help or to subscribe/unsubscribe, email majordomo@eda.org |with just the appropriate command message(s) in the body: | | help | subscribe ibis <optional e-mail address, if different> | subscribe ibis-users <optional e-mail address, if different> | unsubscribe ibis <optional e-mail address, if different> | unsubscribe ibis-users <optional e-mail address, if different> | |or email a written request to ibis-request@eda.org. | |IBIS reflector archives exist under: | | http://www.eda.org/pub/ibis/email_archive/ Recent | http://www.eda.org/pub/ibis/users_archive/ Recent | http://www.eda.org/pub/ibis/email/ E-mail since 1993Received on Mon Jul 11 05:55:46 2005
This archive was generated by hypermail 2.1.8 : Mon Jul 11 2005 - 05:55:54 PDT